In Uppsala CHP Plant, there are six pressure reducing valves to reduce the pressure from 15 to 3 bars, before six absorption heat pumps. During the process the energy is conserved but losses occur in form of exergy. The aim of this thesis is to reduce the losses of exergy. This can be done by letting turbines replace the pressure reducing valves.In this thesis an investigation has been done of the conditions today, the conditions after the change from pressure reducing valves to turbines and a comparison of three different types of turbine solutions. The three examined solutions are one turbine, several Helical screw expanders and several small turbines in parallel with asynchronous generators.The six absorption heat pumps have been divided into two groups; one group of four and one group of two absorption heat pumps.

This thesis applies to a novel steam expander, one part of a steam engine system, a wobble plateengine. The piston in the expander moves axially with the outgoing rotating shaft and is locatedon a plate, why the engine type is called axial engine. When steam is applied to the plungers theplate wobbles creating a rotation on the shaft going thru the wobble plate. The steam expander issupposed to be used in exhaust gas recovery (bottoming cycle) applications and small scaleenergy production. The commissioner is Ranotor Utveckling AB.

There have been, in some rare cases, difficulties with clamping of inserts with U-holesin their tool holder. According to the complaints, the inserts could not be properlyclamped or could fracture when clamped. A study has shown that variations inclamping behaviour are mainly depending by the position of the screw hole in the toolholder and the centering of the screw hole in the insert.The focus of this project has been the centering of screw hole in insert. It has beenshown that the screw holes are not always enough centered in the insert. Theproblem may occur after a certain step in the production, i.e.

The project ?Investment proposal for grinding station for service work of screw feeders? has been performed during the spring semester 2014 for the course Bachelor?s thesis for degree of  Bachelor of science in machine engineering at Karlstad?s University. The project has been performed in cooperation with Fiber Workshop which is a service department in the company Valmet AB. Valmet AB is a company that develops and manufacture soft paper tissue machines. The screw feeder is a part that is used to feed, and squeeze out the water out of woodchips.

Communication can be heard in many different ways and it is important for all businesses, especially in B2B. The construction and maintenance of a brand plays just like the communication a very important part. These parts also have a lot to common and affect each other in a large extent. One problem that may occur in many companies is the failure to grow and gain a larger share of the market even if they in various ways are trying. Expander is one of those companies and in this research report we studied communication and brand building, focusing on brand management, relationships and integrated marketing. Here we drew the conclusion that all these areas are important for a company, especially in the Business-to-Business marketing in different ways.

The purpose with this thesis is to get a compilation of all the critical bolted joints of all enginesproduced at LV Motors. ABB LV Motors produces induction engines with seven shaft heights. Eachengine size exists several variants of components ex. standard shield and flange shield. Depending onwhich components the engine is equipped with arises various types of strains in the engine's parts,certain assembly ways are more favourable than other.The most critical parts in the engine from a mechanical point of view are the screw units betweenshield/stator, feet/stator and bearing cover/shield.

In this thesis tests has been performed on the pull strength of screws glued into glulam beams.The experiment is based on the already approved method whereby the diameter of the drilled holes is the same as the screw outer diameter of 1 mm or bigger. The screws strength class shall not be less than 4.6 (EN ISO 898-1:1999, 1999).The difference in the experiments that were performed where that the drilled diameter were 1 mm smaller than the outer diameter of the screw so that the screw thread was worked into the wood.In the tests the gluing where made on M8 glulam beams. The screws where drilled at and angel of 90°tangental to the fiber direction with a diameter of 7 mm. The gluing of the screws where made in three different depths and where later exposed to pulling forces. The results showed both pulling breaks and screw breaks when they reached their maximum capacity.

The work thesis was performed at Assalub a company which is situated in Åtvidaberg. The company works with developing, manufacturing and marketing equipment for handling of lubricants for light and heavier industry. The work thesis it is based on a inquiry Assalub got from MacGregor which is a company within cargo solution, from port to offshore system.For unloading grain and other material from the ship cargo it is used combined inlet feeder and screw conveyor, there the inlet feeder is drilling down through the cargo and feed the screw conveyer with material to further destination. At the bottom of the screw conveyer and the inlet feeder there is a bearing that keep the parts together. However the lubrication of the bearing must be made manually.

This Master Thesis has been carried out in cooperation with Ursus Medical AB (URSUS) which markets, assembles and sells the Rotex Screw Needle Biopsy Instrument ®. The instrument is delivered with an instrument holder. Customers had expressed dissatisfaction over that they needed to use two hands during a biopsy procedure, which resulted in a project to develop a new instrument holder.The project aim was to create concepts for how the new instrument holder should be designed, with focus on the mechanics. The new instrument holder would build on the existing basic principle that the screw needle and the cannula were screwed into the tissue. The thesis work would result in a technical solution and a functional prototype of the chosen concept.To achieve this, a generic product development processes were used and began with a comprehensive literature review.

This report reflects an examination work performed for Getrag All Wheel Drive AB during the spring of 2005. Among the companies range of products there exists some concern regarding the amount of clamping force and friction on bolted joints caused by the assembly torque.The aim of this project has been to determine if there is a simple way in which to identify and then practically apply testing methods for clamping force and friction through utilization of existing testing equipment.Three separate methods of clamping force and friction determination have been tested in rear drive unit, RDU, at a 30 Nm assembly torque. A fourth and final method, screw elongation with ultrasound, has been used as reference. The methods are:?Torque-Tension test.?Screw elongation with micrometer.?Joint stiffness test.?Screw elongation with ultra sound for reference.The results from tests can be viewed in table below.MethodTorque-TensionMicrometerCs=318 kN/mm Assembled with torque wrenchMicrometerCs=318 kN/mm Assembled on lineUltra-soundCS=311 kN/mm Ultra- soundCS=318 kN/mm Joint stiffnessTheoreticalClamping force-21,8 kN17,6 kN17,3 kN17,6 kN17,1 kN17,3 kNFriction-0,110,1470,1530,1470,1520,149.

The thesis is an examination of the methods that are appropriate and long-term choice to obtain clamping force and secure screw joints in production. The employer, Scania CV AB, transmission manufactures axle gears to all trucks produced in Södertälje. One of the most common assembly elements is screw joints, where the clamping force is essential to achieve a secure joint. Current methods to secure the joint is due much of the friction effect and is an indirect method to measure the clamping force. The clampforce accuracy becomes more widely with torque angle control.

In this study, the pre-tension force in an insert screw connection are examined in order to establish a greater understanding of the system and to facilitate the process of making new metal cutting tools. Certain especially significant design variables such as the offset, the length of the contact thread and the shank length above the threaded hole, are selected to be closely examined. A comparison of the influence on the pre-tension force between threaded holes made with a worn, versus new, threading tool is also involved in the experiment. The study is limited to handling the screw sizes M2,5 and M3,5. The results show that a regression model, with good approximation, can be fitted to the measured values.

Today's society is facing major challenges. In order to reduce the climate impact fossil fuels should be replaced with fuels that do not contribute to the greenhouse effect. The growing population generates organic waste originating from industry and households so called organic fraction of municipal solid waste (OFMSW). Through anaerobic digestion, waste can be utilized to produce energy-rich methane gas. In this way, waste can be a resource instead of a burden on society.

The project Design analysis and proposals of plastic screw caps in Australia was performed at Högskolan Dalarna incooperation with University of Western Sydney, Australia. The Swedish company Tetra Pak, in Lund, were assigner forthe project that was performed 2006-2007. The commission was to do a survey about the packages for non-carbonateddrinks in Australia. The bottles had to be plastic, able to open in one step and with focus on the caps.The project has result in design analysis and a new proposal of a plastic screw cap for the Australian market. Sixbottles were choosen and they were all testet on 20 consumers each with a Likert-scale test.

The project Design analysis and proposals of plastic screw caps in Australia was performed at Högskolan Dalarna incooperation with University of Western Sydney, Australia. The Swedish company Tetra Pak, in Lund, were assigner forthe project that was performed 2006-2007. The commission was to do a survey about the packages for non-carbonateddrinks in Australia. The bottles had to be plastic, able to open in one step and with focus on the caps.The project has result in design analysis and a new proposal of a plastic screw cap for the Australian market. Sixbottles were choosen and they were all testet on 20 consumers each with a Likert-scale test.